Next generation of PowerPC based Single Board Computers featuring Freescale’s MPC8548E PowerQUICC III processor

Overview
Product Specifications
Ordering Information

The next generation of PowerPC based Single Board Computers in the AT series of products features Freescales MPC8548E PowerQUICC III processor integrates the enhanced e500 PowerPC core and advanced features such as DDR2 SDRAM with 1GB, 128 MB of NOR flash, 1GB of NAND Flash, 64KB Serial EEPROM, up to 1 GHz of clock speed, 1MB of NVRAM. The system provides the required interfaces to interface custom modules in the system. The system provides communication bus interfaces like asynchronous communication ports on RS232/422 and two gigabit Ethernet ports. The SBC also features a watchdog timer, Real Time Clock and comes equipped with a single PMC mezzanine site. AT-VME-PADC-MPC8548 provides on-board Analog-to-Digital conversion channels, providing additional resource on-board for high-speed data acquisition applications. The SBC is available in Air-cooled and Conduction cooled temperature versions to suit various applications. Contact sales for more information.

CPU

	Freescale MPC8548E PowerQUICC III processor
	Embedded PowerPC e500 core
	Clock Frequency at 1.0 Ghz
	Two USB 2.0 host ports
	L1 Cache: 32KB of instruction and 32KB of data cache
	L2 Cache: 512 KB

Memory

	1 GB of DDR2 SDRAM with ECC
	128 MB of NOR Flash
	1 GB NAND Flash
	64Kbits Serial EEPROM
	1 MB Non-Volatile SRAM

Bus Interface

	32 bit Local Bus
	Two 32bit/33Mhz PCI r2.2 compliant buses
	VME 32 bit Backplane bus interface

I/O Interfaces

	Two 10/100/1000 Mbps Gigabit Ethernet ports
	One Debug RS232 Serial Port
	Four RS232/RS422 Multiprotocol Serial Ports
	LVTTL Differential IOs - 16 Nos
	LVTTL Single Ended IOs - 16Nos
	Two USB 2.0 Host Ports (Optional)
	PMC User IO on P2 Connector

Others

	Provides a Real-Time Clock (RTC)
	Supports an external battery for Real-Time Clock operation
	Provides Watchdog Timer feature
	Temperature Sensors
	Voltage Monitoring
	Power Sequencing

JTAG

	On-board JTAG chain for FPGA`s
	VME JTAG signals from P1 connector to test/program on-board JTAG devices
	On-board JTAG interface to the processor for debugging and development purposes

Clock

	On-board 80MHz oscillator
	Different clock signals for ADC and DAC
	On-board PLL circuit for clock frequency programmability

On-board Flash FPGA

	User configurable 16- LVDS I/O
	User configurable 16-LVTTL discrete I/O
	Temperature Monitoring
	Voltage Monitoring and Power Sequencing
	Serial EEPROM interface

Analog-to-Digital Conversion Block

	Three DC Coupled Analog input channels (AC Coupling - Optional)
	High Speed AD9445 14 bit ADCs
	Rate of 105Msps for each channel
	High speed 14-bit AD9744 DACs support testability of both analog and digital subsystems
	SMA coaxial front panel connectors
	50 ohm input impedance
	Sampling using Internal clock
	Synchronous and Asynchronous modes of operation
	Programmable Sampling rate selection
	One Virtex-5 FPGA, for additional custom logic
	On-board 80MHz clock Oscillator

PMC Interface

Single PMC mezzanine site on rear I/O

Front Panel Connectors

	One Debug serial port
	One Gigabit Ethernet port
	Three SMA Analog Input Channel Connectors
	Reset Switch

Rear I/O

	Four MultiProtocol RS232 / RS422 Serial Ports
	Two USB 2.0 Host ports
	Two Gigabit Ethernet ports
	PMC User IO on P2 Connector

Mechanical

	6U VME single slot interface
	Dimensions- 233.35mm x 160mm
	Thickness: 2.4mm
	Metal Heat sink covering over the card for efficient heat transfer from the card to the chassis
	Card fitted with wedge locks on either side for firm seating in the slot

Operating Systems Support

	Standard Support for Linux 2.6.x
	Optional Device drivers and BSP for VxWorks (6.3) Operating System

Power

	Derived from +5.0V of Backplane
	3.3V and other voltages required for powering on-board devices are generated from on-board power circuitry

Environmental

	Air Cooled	Conduction Cooled
Operating Temperature	0°C to +60°C	-40°C to +85°C

Warranty

1 year limited warranty