|
 |
|
| AT-XMC/PMC-GPS |
 |
Choice of Bus Interface |
|
XMC x1 Lane PCIe, 2.5Gbps |
|
PMC PCI bus 32-bit, 33MHz |
|
IRIG-B Time Code Input (Digital) |
|
Optional discrete I/O and IRIG-B |
|
Available in 2 variants Air Cooled, Conduction Cooled |
|
Four Discrete Inputs & four Discrete Outputs |
|
Rear P16 or Rear P14 or Front I/O available |
|
DIP Switch Configuration provided to control
transceivers |
|
On Board GPS Module provided |
|
On Board SMA connector specifically for GPS
communication |
|
Optional GPS receiver provided on the card |
|
Front panel connector ( 68 PIN VHDCI ) for easy access
to all Ios |
|
8 Serial Communication ports provided |
|
4 ports provide full functionality |
|
4 ports provide half control ( RS232 / RS422 / RS485 ) |
|
High-level API for Windows XP, Windows 7 & Linux |
| |
|
|
 |
|
|
|
|
|
|
| AT-PXI-DIO-16 |
|
16 input plus 16 output channels per board |
|
Input channels are opto-isolated |
|
TTL/CMOS/0 to 30V input compatibility |
|
Output channels have Solid State Relays |
|
Interrupt generation on any input channels events and
programmable |
|
Galvanic isolation for output channel |
|
I/O signals via Front panel connector |
| |
|
|
|
|
|
|
|
| AT-VME-DIO-32 |
|
VME 6U Board |
|
Based on VME64x Architecture |
|
Available in three variants - Commercial, Air-Cooled,
Conduction-Cooled |
|
Vibration, Shock resistant |
|
Complies with IEEE 1101.2 mechanical specifications |
|
Programmable Interrupter: 7 Levels |
|
Dimensions- 233.35 x 160mm |
|
Isolation and non-isolation options available |
|
Input Voltage: TTL and Open Collector |
|
Optional - Two Asynchronous Channels of RS-232 or
RS-422 or 1 each of RS-232/422 Serial Interfaces |
|
Programmable Baud Rates up to 115.2 k/Bauds |
|
Driver and high-level API libraries for Windows XP, Linux,
RT-Linux, LynxOS 4.0 and VxWorks 5.5
|
| |
|
|
|
|
|
|
|
|
|
| AT-VME-DIO-64 |
|
VME 6U Board |
|
Based on VME64x Architecture |
|
Available in three variants - Commercial, Air-Cooled,
Conduction-Cooled |
|
Vibration, Shock resistant |
|
Complies with IEEE 1101.2 mechanical specifications |
|
Programmable Interrupter: 7 Levels |
|
Dimensions- 233.35 x 160mm |
|
Isolation and non-isolation options available |
|
Input Voltage: TTL and Open Collector |
|
Optional - Two Asynchronous Channels of RS-232 or
RS-422 or 1 each of RS-232/422 Serial Interfaces |
|
Programmable Baud Rates up to 115.2 k/Bauds |
|
Driver and high-level API libraries for Windows XP,
Linux, RT-Linux, LynxOS 4.0 and VxWorks 5.5 |
| |
|
|
|
|
|
|
|
| AT-XMC-PMC-DIO |
|
XMC - x1 Lane PCIe, 2.5Gbps / PMC - PCI bus 32-bit,
33MHz |
|
IPCDIO - DIO processing Core |
|
Input types: TTL Differential, Open/Gnd, 27V/Open or
Casing/Break inputs |
|
Open/GND Inputs and Outputs - 8 Nos Each |
|
27V/Open or Casing/Break Inputs and Outputs - 12 Nos
Each |
|
27V/Open or Casing/Break inputs are opto-isolated |
|
Open/GND inputs diode protected |
|
Output types: TTL Differential, Open/Gnd and 27V/Open
outputs |
|
Discrete Outputs can switch +27V load, either Low side
or High Side |
|
Interrupts programmable on discrete inputs |
|
On-chip Timers for scheduled status reading of
discrete inputs or drive of discrete outputs |
|
Rear P16 or Rear P14 or Front I/O available |
|
Available in two variants -Air Cooled, Conduction
Cooled |
|
High-level API for Windows XP, Windows 7 and Linux |
|
LabVIEW drivers available optionally |
| |
|
|
|
|
|
|
|
|
| Back to COTS Products |
|
|
|
